Publications by authors named "Cheng-Di Dong"

102 Publications

Microwave-assisted gasification of biomass for sustainable and energy-efficient biohydrogen and biosyngas production: A state-of-the-art review.

Chemosphere 2021 Aug 25;287(Pt 1):132014. Epub 2021 Aug 25.

Korea Biochar Research Center, APRU Sustainable Waste Management & Division of Environmental Science and Ecological Engineering, Korea University, Seoul, 02841, Republic of Korea.

Biohydrogen and biosyngas are among the sustainable bioenergy products from biomass resources through gasification. Microwave-assisted gasification (MAG) is still a novel technology, but it is definitely a promising conversion technology to achieve a sustainable bioeconomy. Although this technology shows a massive potential to be fully implemented in the near future, the selectivity and efficiency of biohydrogen and syngas production still need enhancements and further research to secure a cost-effective and energy-efficient industrialization. This article comprehensively reviews the regular, microwave-induced plasma, and catalytic MAG systems in relation to their biohydrogen and biosyngas production, carbon conversion efficiency, and tar removal while discussing the significance of optimal operating conditions and considerations in the gasification system design. Several perspectives such as benefits, challenges, numerical simulations, and scalable opportunities are also explored to provide factual insights for further research and industrial application.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.chemosphere.2021.132014DOI Listing
August 2021

Genetic modification for enhancing bacterial cellulose production and its applications.

Bioengineered 2021 Dec;12(1):6793-6807

Department of Marine Environmental Engineering, National Kaohsiung University of Science and Technology, Kaohsiung City, Taiwan.

Bacterial cellulose (BC) is higher in demand due to its excellent properties which is attributed to its purity and nano size. is a model organism where BC production has been studied in detail because of its higher cellulose production capacity. BC production mechanism shows involvement of a series of sequential reactions with enzymes for biosynthesis of cellulose. It is necessary to know the mechanism to understand the involvement of regulatory proteins which could be the probable targets for genetic modification to enhance or regulate yield of BC and to alter BC properties as well. For the industrial production of BC, controlled synthesis is desired so as to save energy, hence genetic manipulation opens up avenues for upregulating or controlling the cellulose synthesis in the bacterium by targeting genes involved in cellulose biosynthesis. In this review article genetic modification has been presented as a tool to introduce desired changes at genetic level resulting in improved yield or properties. There has been a lack of studies on genetic modification for BC production due to limited availability of information on whole genome and genetic toolkits; however, in last few years, the number of studies has been increased on this aspect as whole genome sequencing of several strains are being done. In this review article, we have presented the mechanisms and the targets for genetic modifications in order to achieve desired changes in the BC production titer as well as its characteristics.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1080/21655979.2021.1968989DOI Listing
December 2021

Evaluation of Chemical Compositions, Antioxidant Capacity and Intracellular Antioxidant Action in Fish Bone Fermented with .

Molecules 2021 Aug 31;26(17). Epub 2021 Aug 31.

Department of Chemical and Materials Engineering, National Kaohsiung University of Science and Technology, Kaohsiung 80778, Taiwan.

Fish bones (FBs) are aquatic by-products that are sources of antioxidant-active peptides, calcium dietary supplements, and biomedical materials. Usually, fermentation of these by-products via microorganisms brings desirable changes, enhancing their value. This study investigates the value addition of FB when fermented with (MP) for different time intervals, such as 3 days (F3) and 6 days (F6). The results indicate that the soluble protein, peptide, amino acid and total phenol content, as well as the antioxidant capacity (DPPH, ABTS radical scavenging activity, and relative reducing power), of F3 and F6 were significantly increased after fermentation. Furthermore, the ROS contents of F3 and F6 were reduced to a greater extent than that of hydrogen peroxide (HO) in Clone-9 cells. The MMP integrity, as well as the SOD, CAT, and GPx activity, of F3 and F6 were also increased significantly compared to the HO in Clone-9 cells. Notably, F3 and F6 displayed significant reductions in ROS content, as well as elevate, SOD activity and MMP integrity in Clone-9 cells, when compared with the native FB. These results indicate that the FBs fermented with MP for 3 days (F3), and 6 days (F6) have antioxidant capacity, with possible applications as natural food supplements.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.3390/molecules26175288DOI Listing
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC8434028PMC
August 2021

The Anti-Obesity Effects of Lemon Fermented Products in 3T3-L1 Preadipocytes and in a Rat Model with High-Calorie Diet-Induced Obesity.

Nutrients 2021 Aug 16;13(8). Epub 2021 Aug 16.

Department of Seafood Science, National Kaohsiung University of Science and Technology, Kaohsiung 81157, Taiwan.

Lemon () has antioxidant, immunoregulatory, and blood lipid-lowering properties. This study aimed to determine the effect of the lemon fermented product (LFP) which is lemon fermented with OPC1 to prevent obesity. The inhibition of lipid accumulation in 3T3-L1 adipocytes is examined using a Wistar rat model fed a high-fat diet to verify the anti-obesity efficacy and mechanism of LFP. Here, it was observed that LFP reduced cell proliferation and inhibited the lipid accumulation (8.3%) of 3T3-L1 adipocytes. Additionally, LFP reduced body weight (9.7%) and fat tissue weight (25.7%) of rats; reduced serum TG (17.0%), FFA (17.9%), glucose (29.3%) and ketone body (6.8%); and increased serum HDL-C (17.6%) and lipase activity (17.8%). LFP regulated the mRNA expression of genes related to lipid metabolism (PPARγ, C/EBPα, SREBP-1c, HSL, ATGL, FAS, and AMPK). Therefore, LFP reduces body weight and lipid accumulation by regulating the mRNA expression of genes related to lipid metabolism. Overall, our results implicate LFP as a potential dietary supplement for the prevention of obesity.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.3390/nu13082809DOI Listing
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC8398352PMC
August 2021

Morphology-dependent MoO/Ni-F nanostructures with enhanced electrochemical hydrogen peroxide detection.

Chemosphere 2021 Aug 20;287(Pt 1):131960. Epub 2021 Aug 20.

Department of Environmental Engineering and Management, Chaoyang University of Technology, Taichung City, 413310, Taiwan. Electronic address:

The present report investigates the various MoO morphologies prepared via different approaches such as morphologies are cubic sheet, ribbon, and hexagonal sheet. These prepared nanostructures are modified as a MoO/Ni-F electrode used to detect hydrogen peroxide (HO). The influence of the morphology on the microstructural, morphological, electronic state, optical and electrochemical properties of MoO nanostructures are systematically studied. The recorded XRD spectra confirmed that the good crystalline nature with the orthorhombic crystal structure. The FESEM analysis shows that preparation approaches strongly influenced the MoO morphology. The elemental mapping and XPS analysis confirm the formation of MoO. The obtained optical band gap values show that the MoO morphology-based bandgap values are 3.38, 3.17, and 2.94 eV. The modified MoO/Ni-F electrode electrochemical impedance spectra show the CP-MoO has good conductivity. Moreover, the CP-MoO/Ni-F electrode has a wide detection window, long-term stability, reproducibility, and a low detection limit is 1.2 μM. Hence, the CP-MoO/Ni-F electrode electrochemical results suggest that the modified electrode has offered a good matrix for toxic contaminants sensing applications.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.chemosphere.2021.131960DOI Listing
August 2021

Synthesizing Various Organic Polyacid Compounds for Modifying Forward Osmosis Membranes to Enhance Separation Performance.

Membranes (Basel) 2021 Aug 6;11(8). Epub 2021 Aug 6.

Department of Fisheries Production and Management, National Kaohsiung University of Science and Technology, Kaohsiung 811213, Taiwan.

In order to overcome the challenges of low permeate flux (J) and the accompanying reverse solute flux (J) during the forward osmosis (FO) membrane separation process, we synthesized four hybrid materials of polyacid-based organic compounds and incorporated them into the selective polyamide (PA) layer to make novel thin-film nanocomposite (TFN) FO membranes. The J and J of each membrane were evaluated and used along with membrane selectivity (J/J) as indicators of membrane separation performance. The fabricated and modified membranes were also characterized for ridge and valley surface morphologies with increasing hydrophilicity and finger-shaped parallel channels in the PSf substrate. Moreover, two highly hydrophilic nanoparticles of graphene oxide (GO) and titanium oxide (TiO) were introduced with the hybrid materials for PA modification, which can further enhance the J of the TFN membranes. The highest J of the TFN membranes achieved 12.1 L/m-h using 0.1% curcumin-acetoguanamine @ cerium polyacid (CATCP) and 0.0175% GO. The characteristic peaks of the hybrid materials were detected on the membrane surface using attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy, evidencing successful incorporation of the hybrid materials during membrane modification. Here, we present the novel TFN membranes using hybrid materials for separation applications. The reactions for synthesizing the hybrid materials and for incorporating them with PA layer are proposed.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.3390/membranes11080597DOI Listing
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC8399665PMC
August 2021

Efficacy and cytotoxicity of engineered ferromanganese-bearing sludge-derived biochar for percarbonate-induced phthalate ester degradation.

J Hazard Mater 2021 Aug 18;422:126922. Epub 2021 Aug 18.

Department of Marine Environmental Engineering, National Kaohsiung University of Science and Technology, Kaohsiung City, Taiwan. Electronic address:

Phthalate esters (PAEs) are a group of ubiquitous organic environmental contaminants. Engineered ferromanganese-bearing sludge-derived biochar (SDB), synthesized using one-step pyrolysis in the temperature range between 300 and 900 °C, was used to enable Fenton-like processes that decontaminated PAE-laden sediments. SDB was thoroughly characterized using scanning electron microscopyenergy-dispersive spectroscopy, transmission electron microscopy, Brunauer-Emmett-Teller surface area, thermogravimetric analysis, Raman spectroscopy, Fourier-transform infrared spectroscopy, electron paramagnetic resonance, X-ray photoelectron spectroscopy, and fluorescence excitation-emission matrix spectroscopy coupled with parallel factor analysis. The maximum PAE degradation was remarkable at 90% in 12 h at pH 6.0 in the presence of 1.7 g L of SDB 900. The highly-effective PAE degradation was mainly attributed to the synergism between FeO and MnO, which strengthened the activation of percarbonate (PC) via electron transfer, hydroxy addition, and hydrogen abstraction through radical (HO•) and nonradical (O) oxidation mechanisms, thereby facilitating PAE catalytic degradation over SDB in real sediments, which clearly proved the efficacy of ferromanganese-bearing SDB and PC for the remediation of contaminated sediments. The cytotoxicity exhibited by human skin keratinocyte cells exposure to high SDB concentration (100-400 µg mL) for 24-48 h was low indicating insignificant cellular toxicity and oxidative damages. This study provides a new strategy for freshwater sludge treatment and reutilization, which enables a water-cycle-based circular economy and waste-to-resource recycling.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.jhazmat.2021.126922DOI Listing
August 2021

Corrigendum to 'Heterologous expression of bacterial CotA-laccase, characterization and its application for biodegradation of malachite green' [Bioresource Technology 340 (2021) Start page-End page/125708].

Bioresour Technol 2021 Aug 20;341:125792. Epub 2021 Aug 20.

Department of Marine Environmental Engineering, National Kaohsiung University of Science and Technology, Taiwan ROC. Electronic address:

View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.biortech.2021.125792DOI Listing
August 2021

Heterologous expression of bacterial CotA-laccase, characterization and its application for biodegradation of malachite green.

Bioresour Technol 2021 Nov 3;340:125708. Epub 2021 Aug 3.

Department of Marine Environmental Engineering, National Kaohsiung University of Science and Technology, Taiwan. Electronic address:

Malachite green (MG) is used as fungicide/parasiticide in aquaculture, its persistence is detrimental as it exhibits carcinogenic effects to aquatic organisms. Bacterial laccase evaluated as the best enzyme at extreme condition for aquatic MG removal. Study aims to increase laccase concentration, CotA-laccase from Bacillus subtilis was cloned and overexpressed in Escherichia coli. Optimal catalysis for purified CotA-laccase were at pH 5.0, 60 °C, and 1 mM of (2,2-azino-di-[3-ethylbenzothiazoline-sulphonate-(6)]) with Km and Kcat 0.087 mM and 37.64 S respectively. MG biodegradation by CotA-laccase in clam and tilapia pond wastewaters and cytotoxic effect of biodegraded products in grouper fin-1 cells were determined. MG degradation by CotA-laccase was equally efficient, exhibiting upto 90-94% decolorization at freshwater and saline conditions and treated solution was non-toxic to GF-1 cells. Thus, recombinant-CotA-laccase could be an environmentally-friendly enzyme for aquaculture to remove MG, thereby effective to reduce its accumulation in aquatic organisms and ensuring safe aquaculture products.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.biortech.2021.125708DOI Listing
November 2021

Effect of molecular mass and sulfate content of fucoidan from Sargassum siliquosum on antioxidant, anti-lipogenesis, and anti-inflammatory activity.

J Biosci Bioeng 2021 Aug 10. Epub 2021 Aug 10.

Department of Chemical Engineering, National Cheng Kung University, Tainan, Taiwan; Department of Chemical and Materials Engineering, College of Engineering, Tunghai University, Taichung, Taiwan; Research Center for Smart Sustainable Circular Economy, Tunghai University, Taichung, Taiwan. Electronic address:

Macroalgae (seaweeds) are abundant in functional polysaccharides known for their unique biochemical activities. In this study, the antioxidant, anti-lipogenic, and anti-inflammatory activities of the fucoidan extracted from brown seaweed Sargassum siliquosum were investigated by 1,1-diphenyl-2-picrylhydrazyl (DPPH)-scavenging ability, lipid synthesis inhibition, and suppression of pro-inflammatory cytokine tumor necrosis factor-alpha (TNF-α) production, respectively. To examine the effect of molecular mass on fucoidan's bioactivities above, the extracted fucoidan was subject to hydrogen peroxide-mediated partial hydrolysis to obtain lower molecular mass compounds within the range of 107.3-3.2 kDa. Results indicated that fucoidan's antioxidant activity increased with a corresponding decrease in molecular mass; the dosage for the half-maximal response (EC) dropped from 2.58 to 1.82 mg/mL when the molecular mass decreased from 107.3 to 3.2 kDa. In addition, both the anti-lipogenesis and anti-inflammatory activities of fucoidan were significantly enhanced by 71.1% and 36.7%, respectively, when the molecular mass decreased to about 3 kDa. To further test the effect of sulfation on fucoidan's bioactivities, low molecular mass fucoidan was treated with SO-DMF to increase the sulfate content. The results indicated that when sulfate content increased from 18.7% to 32.1%, EC of DPPH decreased from 1.82 mg/mL to 0.86 mg/mL and the anti-inflammatory activity also increased by 35.2%; however, the anti-lipogenesis activity decreased.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.jbiosc.2021.06.005DOI Listing
August 2021

A poly-(L-serine)/reduced graphene oxide-Nafion supported on glassy carbon (PLS/rGO-Nafion/GCE) electrode for the detection of naproxen in aqueous solutions.

Environ Sci Pollut Res Int 2021 Aug 12. Epub 2021 Aug 12.

Department of Marine Environmental Engineering, National Kaohsiung University of Science and Technology, Kaohsiung City, Taiwan.

A new electrode was constructed via the anodic electropolymerization of poly-(L-serine) (PLS) on an rGO-Nafion-modified glassy carbon electrode (GCE) for the detection of the emerging organic contaminant naproxen (NPX). The morphology, crystal phase, and surface elements of the electrode were investigated with SEM, TEM, XRD, Raman, ATR-FTIR, zeta potential, C-H-O, and XPS analyses. Results of the surface analysis showed a porous structure resembling graphene sheets inside the Nafion/GCE architecture. Various electrochemical parameters, including scan rate, pH, and NPX concentration, were studied to evaluate the performance of the electrode. The synergistic effect of PLS and rGO-Nafion greatly facilitated the catalytic oxidation of NPX on PLS/rGO-Nafion/GCE. Electrochemical NPX oxidation was a one-electron transfer and adsorption limited process. The optimal working potential was 0.92 V vs. Ag/AgCl. The oxidation current of NPX increased with the increase in the concentration of analyte and scan rate but decreased with pH. The modified electrode exhibited excellent linearity with respect to NPX concentration in the range of 4.3 to 87 μM and limit of detection of 0.23 μM (S/N = 3). The PLS/rGO-Nafion/GCE is a fast, sensitive, reliable, and economical electrode for the detection of NPX in water.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1007/s11356-021-15511-zDOI Listing
August 2021

Assessment of polycyclic aromatic hydrocarbons in seafood collected from coastal aquaculture ponds in Taiwan and human health risk assessment.

J Hazard Mater 2021 Jul 21;421:126708. Epub 2021 Jul 21.

Department of Marine Environmental Engineering, National Kaohsiung University of Science and Technology, Kaohsiung 81157, Taiwan. Electronic address:

The level and distribution of 16 USEPA Polycyclic aromatic hydrocarbon (PAHs) in aquaculture farmed fish (Mugil cephalus and Oreochromis mossambicus) and shellfish (Corbicula fluminea Formosa and Meretrix lusoria) were determined in Taiwan and then assessed cancer and non-cancer risks for those consuming these kinds of seafood. Results indicated that C. fluminea Formosa accumulated the highest average concentration of total PAHs (43.0 ± 11.3 ng/g wet weight) while M. lusoria contained the lowest concentration (20.0 ± 5.8 ng/g) among all species. The low-molecular-weight PAHs were dominant for both fish and shellfish, which consistent with other studies. Notably, parts of high-molecular-weight PAHs were found in shellfish whereas that was little in fish. The calculated hazard quotients (HQ) of all PAHs were smaller than 1 and the incremental lifetime cancer risks (ILCR) for Benzo[a]pyrene were below 1 × 10, suggesting that PAHs in the collected seafood could pose a low hazard to residents. Although the results indicated that the studied seafood is safe for human consumption, children and seniors post relatively higher risks, suggesting that it needs to continue monitoring and control the PAHs concentration in seafood and the associated environments.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.jhazmat.2021.126708DOI Listing
July 2021

The sorption of persistent organic pollutants in microplastics from the coastal environment.

J Hazard Mater 2021 Jul 20;420:126658. Epub 2021 Jul 20.

Institute of Ocean Technology and Marine Affairs, National Cheng Kung University, Tainan, Taiwan, ROC. Electronic address:

Microplastic (MP) pellets were sampled from six sandy beaches around Taiwan in order to investigate the concentrations and compositions of POPs, including: PCDD/Fs, PBDD/Fs, PBDEs, PCBs, PBBs, and their congeners. The concentrations of PCDD/Fs on the surface (C) of MP pellets from the six sampling sites were from 1.9 to 14.6 pg∙g, while the overall concentrations within MPs (C) were from 95.0 to 1110.6 pg∙g. As PCDD/Fs were adsorbed into the inner part of MPs, a ratio of the total concentrations to surficial concentration of MPs (C/C) was as high as 355.2 times. The C/C of other POPs were also significant, such as PBDEs being found up to 8068 times, which could be attributed to artificial addition during manufacturing processes as flame-retardant substances. Primary compositions of PCDD/Fs, PBDD/Fs, and PBDEs on the MPs in our POP congener analysis were all found containing species with higher number of chlorine or bromine, which were adsorbed on the MP surface more easily due to their relative higher K.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.jhazmat.2021.126658DOI Listing
July 2021

Effect of polyethylene microplastics on oxidative stress and histopathology damages in Litopenaeus vannamei.

Environ Pollut 2021 Jul 17;288:117800. Epub 2021 Jul 17.

Department of Marine Environmental Engineering, National Kaohsiung University of Science and Technology, Kaohsiung, 81157, Taiwan. Electronic address:

There has been a significant increase in the microplastic (MP) polluting the ocean in recent time which is regarded as toxic for living organisms. In this study, Fluorescent red polyethylene microspheres (FRPE) were administered intramuscularly to Litopenaeus vannamei juveniles at the concentration of 0.1, 0.2, 0.5 and 1.0 μg (g shrimp), and the survival rate was recorded. Analysis of the hepatopancreas for antioxidant enzyme activity and gene expression were done after seven days. Further tissue morphology and accumulation of FRPE was analysed. The results showed that FRPE at 0.5 and 1.0 μg (g shrimp) reduce the survival rate of L. vannamei. FRPE at 0.5 and 1.0 μg (g shrimp) reduced superoxide dismutase (SOD) activity; FRPE at different concentrations reduced catalase (CAT) activity; FRPE at 0.2, 0.5 and 1.0 μg (g shrimp) increased the lipid peroxide thiobarbituric acid (TBARS) content. FRPE at 0.1, 0.2, and 0.5 μg (g shrimp) significantly affect the performance of SOD and CAT genes; FRPE at 0.2 and 0.5 μg (g shrimp) significantly improves GPx gene performance; FRPE at 1.0 μg (g shrimp) significantly reduced the expression of GPx genes. Analysis of tissue morphology shows that FRPE cause muscle, midgut gland, and hepatopancreas, and gill damage at different concentrations. In the results of accumulation of microplastic, FRPE accumulated in gill tissue at 0.2 and 0.5 μg (g shrimp); FRPE accumulated in gill, muscle and hepatopancreas tissue at 1.0 μg (g shrimp). Based on the above results, FRPE at 0.5 and 1.0 μg (g shrimp) can regulate the antioxidant enzymes of L. vannamei, increase lipid peroxide content, cause tissue damage by accumulating in the tissues. The rate of survival decreased in L. vannamei, and the impact of FRPE at 1.0 μg (g shrimp) was significant.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.envpol.2021.117800DOI Listing
July 2021

Remediation of contaminated dredged harbor sediments by combining hydrodynamic cavitation, hydrocyclone, and persulfate oxidation process.

J Hazard Mater 2021 Jul 6;420:126594. Epub 2021 Jul 6.

Department of Marine Environmental Engineering, National Kaohsiung University of Science and Technology, Kaohsiung City, Taiwan. Electronic address:

A pilot-scale hybrid treatment system consisting of hydrodynamic cavitation (HC), hydrocyclone separator (HS), and sodium persulfate (PS), was employed for removing polycyclic aromatic hydrocarbons (PAHs) from dredged harbor sediments. The effectiveness of PAH degradation was studied by varying the inlet pressure (0-2.0 bar), PS dosage (or Σ[PAH] to [PS] mole ratio of 1:1-1:10) at HS inflow velocity of 2.85 m/s, slurry concentration of 10%, and reaction time of 60 min. The degradation rate of PAH in the overflow (OF) sediment was significantly lower than that of the underflow (UF) sediment. After an inlet pressure increase of 0.5 bar and ΣPAH: [PS] molar ratio of 1: 10, the PAH removal was 87% and 55% in the UF and OF, respectively, by the combined HC-PS-HS unit. Without PS, the PAHs removal was 46% and 40% in the UF and OF, respectively. The removal efficiency for 6-, 5-, 4-, 3-, and 2-ring PAHs was 100%, 93%, 93%, 92%, and 82% in the UF and 55%, 61%, 67%, 47%, and 36% in the OF by the combined HC-PS-HS system. FEEM spectroscopy clarified that aromatic protein-based components (tryptophan- and tyrosine-like combined) were gradually degraded and transformed into soluble microbial metabolites when organic matter content declined during the combined HC-PS-HS treatment. This study provides new insights into the combined HC-PS-HS system for PAH degradation in dredged sediments.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.jhazmat.2021.126594DOI Listing
July 2021

Modifying thin-film composite forward osmosis membranes using various SiO nanoparticles for aquaculture wastewater recovery.

Chemosphere 2021 Oct 18;281:130796. Epub 2021 May 18.

Department of Chemical and Materials Engineering, National Kaohsiung University of Science and Technology, Kaohsiung, 80,778, Taiwan.

This paper describes the fabrication, modification, and evaluation of the performance of thin-film composite (TFC) forward osmosis (FO) membranes for lab-scale aquaculture wastewater recovery using various fumed silica (SiO) nanoparticles. The active polyamide (PA) layers of these membranes were novelly modified using different types of pretreated SiO nanoparticles [virgin SiO, dried SiO, and 3-aminopropyltriethoxysilane (APTES)-modified SiO] and concentrations (0.05, 0,1, 0,2, and 0.4 wt%) to improve the membrane hydrophilicity with minimum particle agglomeration. Results show that the APTES-SiO modified membrane had the highest water flux and selectivity, followed by the dried-SiO modified membrane. The APTES coupling agent notably reduced the SiO aggregation on the membrane surface and improved membrane hydrophilicity. Consequently, high permeate flux and an acceptable reverse solute flux were observed. The optimal SiO concentration for PA modification was 0.1 wt% for all the nanoparticle types. The virgin and APTES-SiO modified membranes were used for aquaculture wastewater recovery. The water recovery rate reached 47% in 84 h when using the APTES-SiO modified membrane, while it reached only 26% in 108 h when using the virgin membrane. With a suitable design of the filtration apparatus and choice of draw solution (DS), the prepared novel TFC-FO membrane containing APTES-modified SiO can be used for recycling aquaculture wastewater into the DS, which can then be reused for other purposes.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.chemosphere.2021.130796DOI Listing
October 2021

Degradation of organic contaminants in marine sediments by peroxymonosulfate over LaFeO nanoparticles supported on water caltrop shell-derived biochar and the associated microbial community responses.

J Hazard Mater 2021 Jul 3;420:126553. Epub 2021 Jul 3.

Department of Marine Environmental Engineering, National Kaohsiung University of Science and Technology, Kaohsiung City, Taiwan. Electronic address:

Sediment is an important final repository of persistent organic pollutants such as polycyclic aromatic hydrocarbons (PAHs). Herein, a novel catalyst of LaFeO nanoparticles supported on biochar was synthesized from water caltrop shell by chemical precipitation. The composite (LFBC) was used as peroxymonosulfate (PMS) activator to oxidize PAHs in real marine sediments. Systematic surface characterization confirmed the immobilization of well crystalline nano LaFeO particles onto the biochar surface. Under optimal conditions, i.e., [PMS] = 3 × 10 M, [LFBC] = 0.75 g/L, pH 6.0, and seawater, the total PAH degradation efficiency was 90%, while that of 2-, 3-, 4-, 5-, and 6-ring PAHs was 52%, 61%, 66%, 56%, and 29%, respectively, in 24 h. The Langmuir-Hinshelwood equation better predicted the PAHs degradation kinetics over LFBC by PMS. Interactions between surface oxygen species at LaFeO defective sites and the graphitized biochar network facilitated the PAHs degradation. Furthermore, changes in the bacterial community during the LFBC/PMS treatment were highlighted to assess the sustainable development of the sediment ecosystem. The LFBC/PMS process enhanced the biological richness and diversity of sediment eco-systems. The major phylum was Proteobacteria initially, while Hyphomonas was the genera after LFBC/PMS treatment of the sediment.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.jhazmat.2021.126553DOI Listing
July 2021

Characterization of waste cell biomass derived glutamate decarboxylase for in vitro γ-aminobutyric acid production and value-addition.

Bioresour Technol 2021 Oct 17;337:125423. Epub 2021 Jun 17.

Department of Seafood Science, National Kaohsiung University of Science and Technology, Kaohsiung City 81157, Taiwan.

Waste biomass of Lactobacillus brevis obtained from in vivo γ-aminobutyric acid (GABA) production was used for value-addition. This study aims to extract glutamate decarboxylase (GAD) and characterize it for in vitro GABA production. Extracted GAD showed an excellent activity for in vitro GABA production. 52 W ultrasonic output was best in crude GAD extraction which was purified by Q HP anion-exchange column followed by Superdex-200 colloid separation column. The molecular weight of the purified GAD was determined to be ~53 kDa, and the K value for L-glutamic acid was calculated ~7.65 mM. Pyridoxal 5'-phosphate (PLP) acted as the best cofactor for GAD. Optimum temperature and PLP dosing were deferring for crude and purified enzyme forms which respectively exhibited at 45°C, 55°C, 200 µmol and 20 µmol whereas optimum pH was the same at 4.5. GAD finds applications in food industries hence its detailed characterization would be promising for commercial exploitations.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.biortech.2021.125423DOI Listing
October 2021

Novel application of microalgae platform for biodesalination process: A review.

Bioresour Technol 2021 Oct 29;337:125343. Epub 2021 May 29.

Department of Marine Environmental Engineering, National Kaohsiung University of Science and Technology, Kaohsiung City 81157 Taiwan. Electronic address:

Freshwater demand is rising worldwide due to largely increasing population and industrialization. Latest focus is to explore the Ocean and saline effluent from industries to produce freshwater in a sustainable way via algal desalination. Current physicochemical desalination technology is not only an energy-intensive and expensive process but also gives severe environmental impact from brine and GHGs emissions. Therefore, it is neither environmentally-friendly nor feasible to countries with limited resources. Biodesalination could be an attractive technology with recent breakthroughs in algal bioprocess with fast growth rate under highly saline conditions to effectively remove salts optimally 50-67% from saline water. Algal desalination mainly occurs through biosorption and bioaccumulation which governs by biotic and abiotic factors e.g., strain, temperature, pH, light and nutrients etc. This review provides a current scenario of this novel technology by an in-depth assessment of technological advancement, social impact, possible risks and scope for policy implications.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.biortech.2021.125343DOI Listing
October 2021

Emerging prospects of macro- and microalgae as prebiotic.

Microb Cell Fact 2021 Jun 5;20(1):112. Epub 2021 Jun 5.

Department of Marine Environmental Engineering, National Kaohsiung University of Science and Technology, Kaohsiung City, 81157, Taiwan.

Macro- and microalgae-based foods are becoming popular due to their high nutritious value. The algal biomass is enriched with polysaccharides, protein, polyunsaturated fatty acids, carotenoids, vitamins and minerals. However, the most promising fraction is polysaccharides (PS) or their derivatives (as dietary fibers) which are not entirely fermented by colonic bacteria hence act as potential prebiotic. Primarily, algae become famous as prominent protein sources. Recently, these are widely adopted as functional food (e.g., desserts, dairy products, oil-derivatives, pastas etc.) or animal feed (for poultry, cattle, fish etc.). Besides prebiotic and balanced amino acids source, algae derived compounds implied as therapeutics due to comprising bioactive properties to elicit immunomodulatory, antioxidative, anticancerous, anticoagulant, hepato-protective, and antihypertensive responses. Despite the above potentials, broader research determinations are inevitable to explore these algal compounds until microalgae become a business reality for broader and specific applications in all health domains. However, scale up of algal bioprocess remains a major challenge until commercial affordability is accomplished which can be possible by discovering their hidden potentials and increasing their value and application prospects. This review provides an overview of the significance of algae consumption for several health benefits in humans and animals mainly as prebiotics, however their functional food and animal feed potential are briefly covered. Moreover, their potential to develop an algal-based food industry to meet the people's requirements not only as a sustainable food solution with several health benefits but also as therapeutics is inevitable.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1186/s12934-021-01601-7DOI Listing
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC8180151PMC
June 2021

Adsorption characteristics of tetracycline onto particulate polyethylene in dilute aqueous solutions.

Environ Pollut 2021 Sep 21;285:117398. Epub 2021 May 21.

Department of Marine Environmental Engineering, National Kaohsiung University of Science and Technology, Kaohsiung City, 81157, Taiwan. Electronic address:

The presence of ultrafine plastics particles and its potential to concentrate and transport organic contaminants in aquatic environments have become a major concern in recent years. Specifically, the uptake of hazardous chemicals by plastics particles may affect the distribution and bioavailability of the chemicals. In this study, the adsorption of tetracycline (TC), an antibiotic frequently found in aquatic environments, on high-density polyethylene (PE) particles with the average size of 45 μm, was investigated. The PE particles were characterized for surface acidity for the first time. Results showed that pH controls the surface charge of PE particles. TC adsorption onto PE particles was rapid as expected following the pseudo-second-order rate law (r > 0.99). Polar forces in addition to specific chemical interactions, such as hydrogen bonding and hydrophophilicity controlled TC adsorption onto PE particles. Parameters, including pH, dissolved organic matter, ionic strength, major cations and anions affected TC adsorption onto PE micro-particles. Results indicated that PE particles can function as a carrier of antibiotics in the aquatic environment, which potentially imposes ecosystem and human health risks.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.envpol.2021.117398DOI Listing
September 2021

Graphene [email protected] TiO nanoparticles as electrocatalyst materials for voltammetric detection of hazardous methyl parathion.

Mikrochim Acta 2021 05 29;188(6):216. Epub 2021 May 29.

Department of Chemistry, College of Science, Princess Nourah bint Abdulrahman University, Riyadh, 11671, Saudi Arabia.

A sensitive voltammetric sensor has been developed for hazardous methyl parathion detection (MP) using graphene [email protected] TiO nanoparticle ([email protected] TiO NP) electrocatalyst. The [email protected] TiO NPs were prepared through the sol-gel method and characterized by various physicochemical and electrochemical techniques. The [email protected] TiO NP-modified glassy carbon electrode (GCE) addresses excellent electrocatalytic activity towards MP detection for environmental safety and protection. The developed strategy of [email protected] TiO NPs at GCE surfaces for MP detection achieved excellent sensitivity (2.359 μA μM cm) and a low detection limit (LOD) 0.0016 μM with a wide linear range (0.002 to 48.327 μM). Moreover, the fabricated sensor shows high selectivity and long-term stability towards MP detection; this significant electrode further paves the way for real-time monitoring of environmental quantitative samples with satisfying recoveries.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1007/s00604-021-04847-5DOI Listing
May 2021

Role and significance of lytic polysaccharide monooxygenases (LPMOs) in lignocellulose deconstruction.

Bioresour Technol 2021 Sep 10;335:125261. Epub 2021 May 10.

Department of Marine Environmental Engineering, National Kaohsiung University of Science and Technology, Kaohsiung City, Taiwan. Electronic address:

Lytic polysaccharide monooxygenases (LPMOs) emerged a decade ago and have been described as biomass deconstruction boosters as they play an extremely important role in unravelling the enzymatic biomass hydrolysis scheme. These are oxidative enzymes requiring partners to donate electrons during catalytic action on cellulose backbone. Commercial cellulase preparations are mostly from the robust fungal sources, hence LPMOs from fungi (AA9) have been discussed. Characterisation of LPMOs suffers due to multiple complications which has been discussed and challenges in detection of LPMOs in secretomes has also been highlighted. This review focuses on the significance of LPMOs on biomass hydrolysis due to which it has become a key component of cellulolytic cocktail available commercially for biomass deconstruction and its routine analysis challenge has also been discussed. It has also outlined a few key points that help in expressing catalytic active recombinant AA9 LPMOs.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.biortech.2021.125261DOI Listing
September 2021

Hydrodynamic cavitation activation of persulfate for the degradation of polycyclic aromatic hydrocarbons in marine sediments.

Environ Pollut 2021 Oct 28;286:117245. Epub 2021 Apr 28.

Department of Marine Environmental Engineering, National Kaohsiung University of Science and Technology, Kaohsiung City, Taiwan. Electronic address:

Hydrodynamic cavitation (HC) coupled with persulfate (PS)-based that resulted in the synergistic degradation of polycyclic aromatic hydrocarbons (PAHs) in contaminated marine sediments. The effects of HC injection pressure and Σ[PAH]: [PS] on the rate and extent of PAH degradation were studied in the pressure range of 0.5-2.0 bar, PS concentration rage of 2 × 10 to 2 × 10 M or Σ[PAH]: [PS] of 1:10-1000, and reaction time of 20-60 min. A pseudo-first-order rate law fitted PAHs removal kinetics well. The degradation rate constant increased with injection pressure, reaching the maximum level at 0.5 bar, then decreased at injection pressure became greater than 0.5 bar. The results showed that PAH removal was 84% by the combined HC and PS process, whereas, HC alone only achieved a 43% removal of PAHs in marine sediments under the optimal inlet pressure of 0.5 bar at PS concentration of 2 × 10 M in 60 min. The HC‒PS system effectively removed PH, PY, FLU, BaA, and CH at 91, 99, 91, 84, and 90%, respectively. The maximum removal of 6-, 5-, 4-, 3-, and 2-ring PAHs was 89, 87, 84, 76, and 34%, respectively. Major reactive oxygen species (ROSs), namely, SO and HO•, were responsible for PAHs degradation. Results clearly highlighted the feasibility of HC-PS system for the clean-up of PAHs-laden sediments in particular and other recalcitrant organic contaminants in general.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.envpol.2021.117245DOI Listing
October 2021

Current understanding of the inhibition factors and their mechanism of action for the lignocellulosic biomass hydrolysis.

Bioresour Technol 2021 Jul 27;332:125042. Epub 2021 Mar 27.

Department of Marine Environmental Engineering, National Kaohsiung University of Science and Technology, Kaohsiung City, Taiwan. Electronic address:

Biorefining of lignocellulosic biomass is a relatively new concept but it has strong potential to develop and partially replace the fossil derived fuels and myriad of value products to subsequently reduce the greenhouse gas emissions. However, the energy and cost intensive process of releasing the entrapped fermentable sugars is a major challenge for its commercialization. Various factors playing a detrimental role during enzymatic hydrolysis of biomass are inherent recalcitrance of lignocellulosic biomass, expensive enzymes, sub-optimal enzyme composition, lack of synergistic activity and enzyme inhibition caused by various inhibitors. The current study investigated the mechanism of enzyme inhibition during lignocellulosic biomass saccharification especially at high solid loadings. These inhibition factors are categorized into physio-chemical factors, water-soluble and -insoluble enzyme inhibitors, oligomers and enzyme-lignin binding. Furthermore, different approaches are proposed to alleviate the challenges and improve the enzymatic hydrolysis efficiency such as supplementation with surfactants, synergistic catalytic/non-catalytic proteins, and bioprocess modifications.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.biortech.2021.125042DOI Listing
July 2021

Seasonal variation of diversity, weathering, and inventory of microplastics in coast and harbor sediments.

Sci Total Environ 2021 Aug 26;781:146610. Epub 2021 Mar 26.

Department of Marine Environmental Engineering, National Kaohsiung University of Science and Technology, Kaohsiung 81157, Taiwan. Electronic address:

Spatiotemporal variations in the abundance of microplastics (MPs) in surface sediments along the southwestern coast of Taiwan (including harbor and coastal regions) were investigated and the diversity, degree of weathering, and inventory of MPs in the sediments further quantified. The spatiotemporal variations of MP characteristics were used to assess possible transport routes of MPs. Results indicated that the average MP abundance in the partially-enclosed harbor region was 79.3 MPs in 1 kg dry sediment (item/kg dw), which was 3-5 times higher than that in the coastal region. Average MP abundance during the dry season (36.5 ± 52.2 item/kg dw) was relatively higher than that during the wet season (22.3 ± 23.2 item/kg dw). The dominant MPs were small (0.1-1.0 mm, 90%), colored (62.3%), and consisted mainly of fibers (54.1%) and fragments (40.5%). Analysis by μFTIR revealed the presence of ten types of polymers in the MPs, with the most abundant being polypropylene (35.1%), rayon (33.2%), and polystyrene (10.0%). Values of the microplastic diversity integrated index (MPDII) indicated that MP diversity was greater in the harbor region (MPDII = 0.62) than in the coastal region (MPDII = 0.51-0.54), and greater during the wet season (MPDII = 0.60) than during the dry season (MPDII = 0.50). As indicated by values of the MP carbonyl index (CI), the MPs exhibited a high degree of oxidation (CI >0.31) that appeared unrelated to spatiotemporal variations. In the dry season, MP inventory was 12.2 tons and the wet season inventory was 8.1 tons. The hydrodynamic forces may be an influenced force for the spatiotemporal distribution patterns of the MPs in surface sediments. MPs could accumulate in the surface sediments during the dry season and resuspend in the wet season with the higher rainfall and then migrate towards the deep sea following the water flow.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.scitotenv.2021.146610DOI Listing
August 2021

Adsorption of copper (II) in aqueous solution using biochars derived from Ascophyllum nodosum seaweed.

Bioresour Technol 2021 May 12;328:124829. Epub 2021 Feb 12.

Department of Marine Environmental Engineering, National Kaohsiung University of Science and Technology, Kaohsiung City 81157, Taiwan. Electronic address:

There has been growing research interest in exploiting biochar for cost-effective. removal of different pollutants. Heavy metals, especially copper II (Cu II) is highly toxic and nonbiodegradable pollutants, and has been major source of environmental pollution. In this study adsorption of Cu (II) on seaweed (Ascophyllum nodosum)-derived biochar was systematically examined. The removal efficiency based on surface property of biochar and type of interactions associated with biochar produced at varying pyrolysis conditions were investigated. The highest removal efficiency of Cu (II) from aqueous media was >99% with 223 mg g Cu (II) adsorption capacity observed by biochar derived at 700 °C and pH 5. Langmuir adsorption isotherm described the adsorption mechanisms of Cu (II) on biochar with cationic and anionic electrostatic attractions, surface precipitation, and pore depositions. Thus, this study shows that waste biomass (seaweed) could be a valuable bioresource for heavy metal remediation from various water bodies.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.biortech.2021.124829DOI Listing
May 2021

Distribution and environmental risk assessment of trace metals in sludge from multiple sources in Taiwan.

J Environ Sci Health A Tox Hazard Subst Environ Eng 2021 22;56(4):481-491. Epub 2021 Feb 22.

Department of Marine Environmental Engineering, National Kaohsiung University of Science and Technology, Kaohsiung, Taiwan.

This study evaluated the level of the contaminant of the heavy metals in sludge from different sources and the ecological risk criteria associated with it was also analyzed to establish its reuse in agriculture. The sludge samples were collected from the water plant (WTP), wastewater treatment plant (WWTP), and industrial water treatment plant (IPT) in Taiwan. The inductively coupled plasma mass spectrometry was used to measure the trace metals in sludge. The pollution level and ecological risk criteria for heavy metals in sludge were also used to evaluate its reuse in agriculture. The result shows the average concentrations of trace metals in sludge for three groups (WTP, WWTP, and ITP). Significant correlations were found between concentrations of Zn-Ag ( < 0.001). The higher values of I showed in ITP, indicated Hg to be a major pollutant. In Taiwan, the regulations did not establish the reuse of sludge in agriculture. However, the concentration level of trace metals in sludge was particularly lower than the regular levels in most groups, like WTP and WWTP groups. The industrial sludge was not recommended for the use in agriculture. The results of this study can be used for regular monitoring to establish a reference for sludge management and application to agriculture.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1080/10934529.2021.1887687DOI Listing
June 2021

Semi-batch cultivation of Chlorella sorokiniana AK-1 with dual carriers for the effective treatment of full strength piggery wastewater treatment.

Bioresour Technol 2021 Apr 28;326:124773. Epub 2021 Jan 28.

Department of Chemical Engineering, National Cheng Kung University, Tainan, Taiwan; Department of Chemical and Materials Engineering, Tunghai University, Taichung 407, Taiwan; Research Center for Smart Sustainable Circular Economy, Tunghai University, Taichung 407, Taiwan. Electronic address:

In this study, process optimization for the microalgae-based piggery wastewater treatment was carried out by growing Chlorella sorokiniana AK-1 on untreated piggery wastewater with efficient COD/BOD/TN/TP removal and high biomass/protein productivities. Integration of the immobilization carriers (sponge, activated carbon) and semi-batch cultivation resulted in the effective treatment of raw untreated piggery wastewater. With 100% wastewater, 0.2% sponge and 2% activated carbon, the semi-batch cultivation (90% media replacement every 6 days) exhibited a COD, BOD, TN and TP removal efficiency of 95.7%, 99.0%, 94.1% and 96.9%, respectively. The maximal protein content, protein productivity, lutein content, and lutein productivity of the obtained microalgal biomass was 61.1%, 0.48 g/L/d, 4.56 mg/g, and 3.56 mg/L/d, respectively. The characteristics of the treated effluent satisfied Taiwan Piggery Wastewater Discharge Standards (COD < 600 mg/L, BOD < 80 mg/L). This innovative approach demonstrated excellent performance for simultaneous piggery wastewater treatment and microalgal biomass production.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.biortech.2021.124773DOI Listing
April 2021

Adsorptive removal of dye in wastewater by metal ferrite-enabled graphene oxide nanocomposites.

Chemosphere 2021 Jul 31;274:129518. Epub 2020 Dec 31.

Environmental Engineering Program, National Graduate School of Engineering, University of the Philippines Diliman, Quezon City, 1101, Philippines; Department of Chemical Engineering, University of the Philippines Diliman, Quezon City, 1101, Philippines. Electronic address:

Dyes are hazardous compounds commonly found in industrial wastewaters. Efficient and inexpensive removal of dye molecules from the water matrix has been demonstrated by adsorption processes. Magnetic nano-adsorbents, such as metal ferrites, can be efficiently recovered from the reaction mixture after treating the pollutant. Herein, [email protected] (M = Cu, Co or Ni) was synthesized via solution combustion method for the removal of dye molecules from aqueous solutions. The characteristics of the [email protected], including surface area and pore diameter, surface functional groups, and elemental composition, were examined. Methylene blue was used as representative dye pollutant. Batch adsorption results conformed to the Langmuir isotherm. Maximum adsorption capacities of the [email protected] (M = Cu, Co or Ni) were 25.81, 50.15 and 76.34 mg g, respectively. Kinetics of methylene blue adsorption fitted the pseudo-second-order model. Overall, [email protected] exhibited the highest adsorbent performance among the graphene-metal ferrites investigated, primarily because of its high specific surface area and presence of mesopores.
View Article and Find Full Text PDF

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.chemosphere.2020.129518DOI Listing
July 2021
-->